When there is a breakdown of engineering systems in a private house, then it’s time to joke: here comes the hour of reckoning for several years of amenities. The failure of the treatment plant seems to stop life in the house - now there is no way to arrange a full cleaning, nor to wash, or to wash.
Calling a specialist is not always possible, so you have to repair the TOPAS septic tank and carry out maintenance on your own. Let's look at the septic tank device and the most common breakdowns that can happen.
Briefly about the principle of the station
When starting to repair a treatment plant, it is necessary to have an idea of the principle of its operation. The device is based on the treatment of household liquid waste with bacteria.
And if non-volatile systems rely on the work of anaerobic bacteria, whose vital activity is possible in the absence of oxygen, the Topas treatment plant cleans waste thanks to anaerobic and aerobic organisms.
The difference in the living conditions of these microorganisms also affects a completely different principle of operation of wastewater treatment devices.
Different models of the TOPAS station may differ in size, capacity, and the ability to process a certain amount of effluent per unit time (volley discharge indicator), by the presence of a drainage pump to remove purified water or its absence, installation depth (for example, models marked “Long” are connected to a pipe that lies at a depth below 0.9 m)
In conditions of complete absence of oxygen, the waste material is fermented by anaerobes. The process takes place in the first compartment of the treatment plant. Then, the settled and fermented wastewater is placed at the disposal of aerobes located in the next three compartments of the system.
Aerobic microorganisms break down and process suspended particles and impurities that are in the drains much faster, but they require a constant flow of oxygen. In addition, oxygen is necessary for the oxidation of the mass. Aeration of the sewage is provided by an electric pump, so the device cannot operate without power supply. Read more about how aerobic and anaerobic bacteria work for septic tanks.
Septic tank device and cleaning technology
The septic tank is divided into four independent tanks, and each performs a special function.
The chambers are interconnected in such a way that with an intensive supply of effluents, the purification process is accelerated, and with a small one it becomes more efficient due to the multiple distillation of waste.
Since the flow of wastewater is irregular in households, this feature is very important for the quality and uninterrupted operation of the station.
The septic tank's performance is selected based on the number of permanent residents in the house and the rate of water consumption. A larger number of people a cleaning station can serve only short-term
Operation in continuous fluid flow mode
In the case of continuous flow of wastewater, the process occurs as follows:
- Through the inlet pipe (1), the effluent enters the first receiving chamber (A) (or, as it is also called a surge tank). There they are mixed with previously received waste, large particles settle. As soon as the drains reach a certain level, the sensor is triggered.
- Automation includes an airlift (3), which pumps the drains through a filter that performs rough cleaning (2) and a hair trap in the second chamber (B). Also included is a compressor (7) that supplies air.
- In aeration tank (second chamber B), sewage is biologically treated using biologically activated sludge: large particles are split into smaller ones, and organic matter is processed by aerobes. Bubbles of oxygen injected here at the same time provide mixing of effluents with activated sludge, and it acts as an adsorber, linking suspended particles.
- A bubbling mixture of sludge and effluent enters the third compartment - the secondary sump (B), pumps their recirculation airlift (4) through the tank in the form of an inverted pyramid. Here there is a separation of purified water from activated sludge.
- The sludge separated from the liquid component enters the stabilization compartment (G), and the clarified water is discharged outside the station through the outlet pipe of the device (9).
The station, with the exception of scheduled inspections and cleaning, does not require user participation - all processes proceed automatically. The purified water can be drained into the ground, an absorption well, a gutter, and used for irrigation.
Image Gallery
Photo from
Visual inspection of the station
Cleaning airlifts and flushing nozzles
Septic tank compressor and spare parts
Sludge drainage pump
Reverse phase
If the system does not receive enough wastewater for its continuous operation, the installation operates in recirculation mode. As soon as the level in the first compartment (A) reaches the set minimum value, the float switch (10) is activated.
The switch acts on the solenoid valve and the drains go through the entire cleaning process again.
The recirculation mode occurs in the following sequence:
- In the receiving tank (A) aeration of wastewater takes place.
- After the aeration tank (B), the effluent is pumped into the stabilization compartment of activated sludge (G). There, the precipitate is divided into fractions.
- Old and heavy sludge sinks to the bottom of the chamber (G), while light sludge, together with clarified effluents, goes back to the first chamber (A).
As soon as the water mirror in the surge tank (A) reaches its maximum, the system switches to direct continuous cleaning.
It is considered normal if during the day the liquid waste goes through 5 cleaning cycles. So that the unit can operate in recirculation mode, do not overload it
How to avoid breakdowns?
An important detail in the prevention of breakdowns is the proper installation of the topop septic tank. In addition, like any device or mechanism, a wastewater treatment system requires regular technical inspection. It consists in a visual assessment of the work, the pumping of accumulated sediment.
During the inspection, you may have to eliminate blockages or carry out a minor repair of the TOPAS installation. The regularity of preventive measures is set out in the table.
Each of the above measures should not be neglected. The successful operation of the device directly depends on them.
The design of the septic tank is made in such a way that all elements can be removed and washed, and the filter of large sewage from the collected hair can be cleaned. Sludge from the stabilization chamber must be pumped out at least once a year. If the water in the water supply system is hard, the station needs to be cleaned more often.
Image Gallery
Photo from
Regular assessment of technical condition
Inspecting and flushing the air filter
Cleaning airlifts of possible blockages
Alarm monitoring
Removal of sediment from the stabilizer
Checking float switches
Wall washing inside the station
Pumping sludge from an absorbing well
Removing accumulated sludge from chambers
The longer the sewage treatment plant works, the greater the content of sludge and sewage in it, the more the compressor filter is dirty. Therefore, equipment requires regular cleaning.
All work is performed in a certain sequence:
- Disconnect the device from the power supply. This will allow sludge to settle to the bottom and make it possible to safely clean the compressor filters.
- Unscrew the screws from the compressor covers to have access to the filters. The filter in the form of a foam pad is removed and shaken out. If it is very dirty, it is washed under running water and dried. The covers are put back in place and tightened.
- Within 15 minutes, the sludge settles and you can start pumping. To do this, lower the drainage pump to the very bottom of the sludge stabilizer chamber and pump out the sediment until the water level drops by 50 cm.
- Next, the aeration tank is cleaned. Sludge is pumped from the bottom, lowering the water mirror by 15 cm.
It is not necessary to completely pump out activated sludge, because it helps to clean sewage.
The consistency of settled sediment resembles thick sour cream, but a conventional drainage pump does its job perfectly. Sludge evacuated from a septic tank can be dried and used to feed plants
Clear all device items
The next step is to clean the airlift and filter for large fractions:
- Before removing the hoses of the Mamut pump and filter, mark one of the tubes and the pipe to which it is attached with electrical tape so as not to confuse them in the future (they have different capacities).
- Disconnect the flexible tube from the pump pipe. If it is poorly removed, the joint is warmed up.
- They take out the airlift tube and blow it under the pressure of water or air.
- The filter of coarse fractions is removed. It is washed outside, the collected garbage is shaken out in a bucket, the holes are cleaned of hair clogged in them, and the filter is washed from the inside.
- Then the hair trap is removed and cleaned.
The final stage - washing under pressure of the walls and tubes of the station, collecting floating debris. Before starting work, close the compressors with cellophane to protect them from water. Rinse start with the upper elements.
With the help of a special device - it can be a colander tied to a long bar - collect garbage from the surface of drains
A good pressure of water, which is able to flush old deposits, gives the high-pressure apparatus.
Assemble the system in reverse order. Hose markings can be left for future maintenance work. The next cleaning can be done after 6 months.
Since the volume of the station contents after cleaning has decreased, it must be replenished by pumping water to a normal operating level. The sludge stabilizer chamber is filled to the outlet, the aeration tank - to the gravity exit of the installation
Evaluation of the operation of the device for water quality
A working sewage treatment plant at the outlet gives practically clean water without impurities and extraneous odors. It can be used for watering lawns, flower beds, and a garden. If the water from the device flows cloudy, this indicates a poor cleaning.
The culprit may be the short life of the station (up to one month): the new equipment does not have a sufficient amount of biologically active sludge, which plays the main role in wastewater treatment. Biological equilibrium can be established faster by adding activated sludge from an already operating station.
This also happens due to changes in external conditions: a sharp decrease in temperature, indicating an increased acidity of the pH of the wastewater or the discharge of chemicals (for example, containing chlorine) in them. Usually, when these reasons are eliminated, the situation normalizes by itself.
If clouding of the effluent is constantly observed, then the most probable reasons can be called an increase in the number of effluents, insufficient aeration. The latter sometimes happens due to damage to the distribution tubes and oxygen leakage.
The quality of water treatment can be determined visually by taking a sample. To do this, from the working device in the compartment of the aeration tank, seethe fluid is collected in a container of glass with a volume of about 1 liter. A properly working installation will have a ratio of settled sludge to clear water of 2: 8.
If the sludge is less, it means that the installation is not yet fully ready for operation or insufficiently loaded with sewage. If more, then this probably means that the system cannot cope with a large amount of liquid household waste or the float switch is set low in the compartment and does not switch to recirculation mode.
The selected mixture is allowed to settle for about half an hour. By this time, activated sludge settles, and transparent water rises to the top
Damage to the treatment plant and methods for their correction
Almost all breakdowns of the pumping station are manifested by an increase in the level of effluents in the receiving compartment. Raising the level activates an emergency float, thanks to which an alarm is triggered - a bell or a light signal. Thus, the user learns about the dangers of flooding the system and the discharge of untreated sewage outside the device.
Wastewater treatment plant
First of all, it is necessary to check whether the channel for removing treated effluents from the device is possibly clogged or frozen. If not, then you need to look for the cause of the station flooding based on the type of equipment. It can be with a gravity drainage system or with forced pumping.
For forced pumping units, the problem may be a breakdown of the drain pump or sticky float switch. To check the operation of the pump, it is removed and connected to another outlet. If the pump is in order, but after connecting to the station does not turn on, then, most likely, the matter is in the float switch - it is necessary to replace it.
The flooding of the TOPAS septic tank often requires serious repairs and this is the most common malfunction. If a problem is detected, the first thing to do is disconnect the equipment from the network, remove the compressors, dry them, as well as all the electrical elements of the station during the day
The following problems may be common to gravity and forced models. Check if fluid is being pumped from the receiver compartment to the aeration tank. If not, then the culprit is the malfunction of the airlift.
The causes of failure can be the following:
- damaged airlift tube;
- clogged airlift of the main pump;
- defective float switch;
- damaged compressor membrane, which supplies air to the airlift.
Failures are repaired by replacing damaged items or cleaning clogged areas.
RCD tripping and problems with power supply
If an RCD (residual current device) trips when the station starts, the cause may be a damage to the compressor or the drain pump, the float switch. It is also necessary to check the wiring, sockets.
Disturbances in the operation of the installation can also be caused by a prolonged blackout, and then there is a chance of overfilling of the tanks and the occurrence of an unpleasant odor in connection with the beginning of the development of anaerobic microorganisms. With voltage drops in the network within 3% of the nominal value, it is necessary to install a stabilizer.
Change in water level in an idle station
It is undesirable to leave the TOPAS cleaning system for a long time without work.
But if this still happened, and it was found that the water level in the tank is changing, then the possible malfunctions may be as follows:
- Damage to plumbing fixtures, which leads to water leakage. You need to find the source of leaks and carry out repairs or replacements.
- Damaged device case. If the problems are small, then you can try to solder the case, if not, you need to contact the professionals for help, and they will replace the damaged area. And it’s good if you can get along with the repair, because replacing the entire case will cost a lot.
- Incorrect installation and, as a result, flooding by rain or flood water.
- The tank of the station should be installed so that the lid rises above the ground by 15 cm.
A poorly organized release of purified water from the system can also become a problem. A poor outflow capacity can aggravate a situation of poor outflow.
Guided by the scheme, it is necessary to exclude less likely causes of breakdowns and track possible malfunctions and methods for their elimination
Operation tips
Violation of the operating rules deprives the consumer of the right to warranty service. They also say that maintenance and repair of WWTP TOPAS can only be carried out by specialists of service companies or persons who have studied the installation instructions and have been instructed in safety measures.
Also on our website there is an article on how to properly maintain the Septic tank Topas in winter - read on.
For long-term and successful use of the station, it is necessary to conscientiously implement the recommendations, namely:
- It is forbidden to make design changes to the device of the station;
- it is unacceptable to drain various chemicals, products containing chlorine (in large quantities), water obtained from the regeneration of treatment systems for drinking water;
- It is forbidden to dump construction waste, biodegradable compounds, food residues and cleaning of forest mushrooms, and pet hair into the sewer system.
Despite the numerous prohibitions, the manufacturer fully admits the reasonable use of modern detergents and hygiene products:
- it is allowed to dump toilet paper into the sewer system;
- it is possible to drain drains of chlorine-free washing and dishwashers;
- it is allowed no more than once a week to drain a small amount of cleaning products for plumbing, kitchen equipment, sanitary ware;
- it is allowed to dump kitchen drains without restrictions.
In addition, during a power outage, water consumption should be minimized to prevent overfilling of chambers and spills of contaminated water.
In winter, the lid of the septic tank must be cleaned of the formation of a snow cap so that compressors forcing air have access to it. The device must be insulated at temperatures below -25 ° C
The planned cleaning of the TOPAS station is available in the video material:
Video about the repair of the station after flooding:
It is quite possible to independently clean and repair VOC TOPAS. But, in order to be able to take advantage of warranty service, it is better to ask the manufacturer or seller what kind of work the users themselves are allowed to carry out. Otherwise, interference with the system may invalidate the right to free service.
Do you have any questions after reading the material? Or have you ever encountered a septic tank breakdown and you have something to advise our readers, please leave comments, share experiences, ask questions, and we will try to answer them promptly.