A pumping station is a popular version of equipment for organizing autonomous water supply for a private house. These are reliable and relatively compact devices that can provide high-quality water delivery to all points of consumption.
The equipment is not cheap, so before buying it is necessary to weigh the pros and cons, study the characteristics and compare them with the upcoming operating conditions. Agree, at first glance the task seems quite complicated.
We will show you how to choose a pumping station, describe the device and the principle of equipment operation, and also outline the main criteria for a competent purchase. In addition, we compiled a review of popular brands whose products have won the trust of users. The information in this article will help you make the right choice.
How does a pumping station work?
A pump station is a complex of devices consisting of a pump, a hydraulic storage tank with a rubber or membrane insert, a pressure switch and a control panel.
The principle of operation of the station is quite simple. The pump pumps water into the hydraulic tank, here the water is under a certain pressure, which depends on its quantity and the volume of air in the tank. As water is consumed, the pressure in the accumulator decreases.
Image Gallery
Photo from
Pumping station at the cottage
Private house water supply
Use as booster pump
Providing a supply of water for domestic needs
An appropriately configured pressure switch detects a change in the amount of water. Upon reaching the minimum settings, the relay switches on the pump so that the hydraulic tank is filled with water. As the tank fills, the pressure increases, the relay fixes its maximum level and turns off the pump.
The on and off cycle is repeated in such a way that the tank constantly contains the amount of water that can meet the needs of the residents of the house.
Such a system is highly efficient. For example, if the water supply was connected directly to the pump, the equipment would have to be turned on every time someone opened the tap.
The basis of a pumping station is a pump of any system, but most often a centrifugal type. Its work is controlled by pressure sensors and a hydraulic accumulator equipped with an elastic membrane that responds to changes in the volume of water (+)
The presence of a pumping station with a hydraulic tank allows you to reduce the number of on / off pump to the required minimum. This significantly saves the life of the equipment, extends its service life. Since the water in the hydraulic tank is under pressure, a good pressure can be created in the entire water supply system of the house.
An acceptable indicator is usually about 1.5 atm, but it can be increased if necessary. Separate household appliances (washing machines and dishwashers, jacuzzi bathtubs, showers with hydromassage) in the absence of sufficient pressure in the water supply system simply can not work.
The pump station effectively solves this problem.
This diagram illustrates the structure of the pumping station and the principle of operation of such equipment: water enters the hydraulic tank, which is filled in automatic mode (+)
If, for some reason, access to water is limited or absent (breakdown of the pump, a sharp decrease in the flow rate of the well, etc.), the supply of water in the hydraulic tank will be very useful.
Water can be used for some time until access to water resources is restored. If a pump is used instead of a station, turning it off automatically deprives water of all the residents of the house.
Features of installation and operation
The pump station can be assembled independently, but it is easier to buy a ready-made unit. These devices are relatively simple in installation and operation.
To install the station you will need a flat area and shelter from the weather. The hose of the surface pump is lowered into the well or well, the hydraulic tank is connected to the water supply system of the house, and I provide the entire system with power (RCD will be needed).
Before installing the pumping station, you should choose a suitable place for it, equip a solid base and provide protection from the weather.
After that, it remains to configure the pressure switch and start operating the station. Further intervention in the operation of the device is usually not required.
The station will replenish the supply of water in the hydraulic tank in automatic mode. It is recommended that approximately every three months, the operation of all elements of the pumping station be checked. As necessary, carry out maintenance of individual components: flushing the pump, adjusting the pressure switch, replacing the membrane in the hydraulic tank, etc.
If the pumping station is selected and installed correctly, it can work for many years without interruption.
Image Gallery
Photo from
Purity of water as an argument of choice
Pumping water from an Abyssinian well
Work on pumping water from a well
Open water abstraction
The problem of choosing a pumping station
Such equipment is offered to the consumer in a very wide range.
Models of modern pumping stations differ in a whole set of parameters, such as:
- price;
- equipment;
- place of manufacture;
- brand name
- performance;
- accumulator volume;
- power consumption;
- design features;
- equipment, etc.
When choosing a specific pump station model, you should first carefully study its operating conditions. If a well serves as a source of water intake, you should carefully study the construction passport, it contains a lot of useful information.
If there is no special technical documentation, you will have to find out the characteristics of the well yourself.
Here is a list of indicators that you should focus on when choosing a pumping station:
- well / well flow rate, i.e. amount of water delivered per unit of time;
- statistical and dynamic water level in the well;
- the height at which water will have to be supplied;
- distance from the source of water to its place of consumption.
Productivity is one of the main indicators when choosing a pumping station. It characterizes the maximum amount of water that can be delivered to a house in a certain period of time.
First you need to calculate exactly how much water is needed. This takes into account the number of people living in the house permanently, as well as the presence and characteristics of household appliances that use water: a washing machine, bathtub, hydromassage, etc.
Pumping stations are used as units for water intake from underground and open water sources. They are able to pump water from a depth of 8 - 10 m and transport it to a height of 12 - 30 m, depending on the technical capabilities laid down by the manufacturer (+)
In this case, the parameters of the pumping station should be correlated with the data on the flow rate of the well or well. Problems may arise if water is taken from the source more intensively than natural replenishment. In such a situation, there is a chance that one day the well or well will be empty.
And this will lead to the equipment in dry running mode. Therefore, if the performance of the pumping station significantly exceeds the flow rate of the structure available on the site, it is worth looking for a more suitable model.
Typically, for the organization of autonomous water supply in a private house, pumping stations are selected, the capacity of which varies between 3-6 thousand l / h.
To roughly imagine the necessary equipment performance, you can focus on the following information:
- Peak water consumption at the summer cottage is usually about 0.8-1.5 cubic meters. m / h
- A family of 4-6 people living in a medium-sized cottage consumes about 1.5-2 cubic meters. m / hour.
- For a large country house, taking into account the need for watering, maintenance of the pool, fountains, etc. the need for water will be at least 3-4 cubic meters. m / h
The power of the pumping equipment can be 0.6-1.5 kW. Here, not only the amount of water that needs to be pumped into the house is important, but also the distance from the point of water intake to the point of its consumption, as well as the height that the water column will have to overcome in order to get into the house.
The more these indicators, the more powerful equipment should be chosen.
The depth at which water has to be taken can be of decisive importance. Typically, pumping stations are equipped with a surface self-priming pump, which is effective at a depth of 6-8 m. Owners of deeper wells, as a rule, should use more powerful submersible pumps.
You can solve the problem using a self-priming pump with a remote ejector. This is a more complex device, but it allows you to increase the depth of water intake to 30 meters and even more. Moreover, such equipment can be used in standard four-inch wells.
Of course, the dimensions of the hydraulic accumulator tank deserve attention. You should not choose a container that is too large in volume, since it will gain significant physical weight when filled with water. Water tanks are usually made of stainless steel, as well as cast iron or plastic.
The hydraulic tank of the pumping station should provide a sufficient head and supply of water, however, an overly large device should not be purchased
For long-term use, taking a plastic container does not make sense, it has a too short life. Cast iron tanks are exceptionally reliable, but have a high cost. Light, relatively inexpensive and strong steel is most often used for the manufacture of hydraulic tanks.
The inner liner made of rubber may be pear-shaped or in the form of a membrane. Since this element experiences a constant and at the same time changing load, it may fail over time. When choosing a pumping station, it makes sense to think about the possibility of replacing the tank liner.
The cost of the pumping station can be significantly affected by the presence of protective modules. This equipment allows you to automatically turn off the pump, if the source has run out of water. If you do not turn off the equipment on time, working in idle mode will cause the engine to overheat, which will lead to significant damage.
In some cases, it is necessary to completely replace the engine, pump or the entire station. Is it worth it to spend money on a pumping station with an automatic control unit? On the one hand, this is a very convenient module, on the other - additional expenses.
Image Gallery
Photo from
Centrifugal pump station
The specifics of the use of vortex aggregates
Self-priming centrifugal pump
Station multi-stage pump
In almost all cases, automation is an appropriate acquisition, especially when it comes to supplying a large house with water for a whole year. Manual control of a pumping station should be considered only if it is purchased for a small cottage where such equipment is used irregularly.
Recommendations for the selection of equipment
Pumping station - equipment is not cheap. Choosing the right model, it makes sense to pay attention to the products of well-known brands with a good reputation.
Too low a price is not the best indicator for a pumping station. Typically, such units have quality problems that occur only during operation.
Image Gallery
Photo from
Having decided on the volume of the tank, the type and performance of the pump, you should pay attention to the technical options of the system
A strong case for acquiring a machine is the ability to independently conduct simple maintenance operations
Well, if the equipment is equipped with an economical mode of energy consumption with smooth adjustment, allowing you to choose the optimal position
Significantly prolong the life of the pump and eliminate the need to repair the station; protection device against overheating of the motor
To prevent clogging, the pump station is equipped with an integrated filter. From the burnout of seals and, as a consequence, damage to the engine, the check valve will save
Wide throat will provide easy refueling of the working part of the pump with water, a convenient handle will facilitate carrying if necessary
For automatic station operation in normal mode, self-priming units are priority, both nozzles of which are located above the central axis of the machine
As a convincing argument in favor of a particular technique, the service life of the tank and pressure switch should be used, the replacement of which during operation is undesirable
Technical options of pumping stations
Prevention of blockages and breakdowns
Economy mode of operation of the station
Built-in engine protection
Debris and dry running gear
Ergonomics of operation and ease of preparation
Pipes for self-priming pumps
The real working life of automation and hydraulic accumulator
The most important point is after-sales service and warranty. The product must be equipped not only with a technical passport and detailed instructions, but also with duly executed warranty documents, which should be carefully studied.
A long warranty period for an automatic pumping station usually indicates its high quality. You should also familiarize yourself with the procedure for providing warranty services.
It so happens that to repair a pumping station under warranty you have to go to the nearest city, region or even send broken equipment to a neighboring country, and this is a long and extremely inconvenient one.
At the end of the warranty period, repairs and maintenance will have to be done independently. You need to make sure that the materials, spare parts and components necessary for this are on sale, so that you do not have to wait for months to deliver the item you need to repair the station.
Over time, even the best pumping station can fail. Uncomplicated repairs can be carried out on your own with suitable materials and spare parts.
Usually there are no big problems with pumping stations of well-known foreign companies, since they have not only a wide dealer network, but also an established system of after-sales service for their products.
It is worth paying attention to domestic products, which with high quality can offer more attractive prices for pumping stations.
Recommended Models
Marina APM 100/25
This is a fairly powerful Italian-made pumping station with a sturdy cast-iron casing. It is designed to pump clean water.
Cast iron pumping station Marina APM 100/25 made in Italy, distinguished by high performance and increased reliability
The power consumption of the equipment is 1.1 kW, the capacity is 2400 l / h, the available immersion depth is 25 m. Such a pumping station is perfect for servicing a relatively large cottage.
Grundfos Hydrojet JPB 6/24
The pumping station from a well-known Italian brand, consumes 1,400 watts of electricity, while it allows you to get about 5 cubic meters. m of water per hour.
Grundfos JP 2 PT pumping station, a product of a well-known Italian company, supplies water from a depth of 8 meters, suitable for a summer cottage or a small cottage
The immersion depth of this device is relatively small - only 8 m. It is designed for operation in moderate latitudes and is of high quality, however, like all products with the GRUNDFOS logo.Suitable for giving or a small cottage.
Gardena 4000/5 Classic
This unit consumes a little - only 0.85 kW with a quite impressive performance, which is about 3,500 l / h.
The GARDENA 4000/5 CLASSIC pump station is characterized by high productivity - 3500 l / h - with a relatively low power consumption - only 850 W
This is a universal version of the pumping station, which can be used for the needs of the house and the surrounding area. Use such equipment even to service water supply nodes.
Jumbo 50/28 H-24 and Jumbo 70/50 N-50 N HOUSE
Jumbo Jilex pumping stations are very diverse. The performance of these devices, immersion depth and power vary in a fairly wide range, which allows you to choose a model that is ideal for specific conditions.
Jumbo Gileks pumping stations are the most popular choice in Russia, because at a reasonable price they demonstrate a high degree of reliability
For example, Jumbo 50/28 H-18 with a capacity of about 3 m³ / h is suitable for a small cottage.
And here Jumbo 70/50 N-50 N HOUSE can be used in a medium-sized cottage. Some models are additionally equipped with an ejector, which can significantly increase the depth of immersion. The cost of pumping stations of this manufacturer is relatively low, while the reviews on product quality are mostly positive.
AQUAROBOT M
This is a series of water pumping stations designed specifically for low debit water sources. Such models are relatively inexpensive, the power of the pumping station is less than 250 watts. Such a unit can be an excellent choice for a summer house or a small house.
AQUAROBOT M pump station is the most suitable option for low flow rate water sources. The unit is characterized by low power, only 250 watts
AL-KO HW 4000 FCS Comfort
This is the ideal solution for deep wells. For wells, this compact model can also be safely used. A power of 1000 W allows you to lift water from a depth of 45 m. The maximum capacity is 4 m³ / h.
The AL-KO HWA 1300 F pump station is perfect for wells up to 50 meters deep. It will provide water not only to the house, but also to the plot
Such pumping stations will provide the necessary pressure in the house, as well as carry out watering work on the site.
Wilo Jet HWJ 203 50L
This is a pump station with an open tank. With a power of 1000 W, it can be used to draw water from a depth of 42 m. Productivity at the peak will be 5 m³ / h.
For work in difficult weather conditions, the pumping station of the famous Wilo Jet HWJ 203 brand, made of durable materials, is ideal
All units manufactured under the Wilo brand are highly reliable. This type of equipment is designed to operate in harsh climates.
Whirlwind ACB-800/24
It is a small pumping station, popular in dachas and in private houses, but equipped with a spacious hydraulic tank. The maximum immersion depth is 9 m, power - 800 W, productivity - 3.6 m³ / h, average price range. All this made the Whirlwind pumping stations extremely popular.
Pump station “Whirlwind” - a relatively inexpensive unit, but reliable and very popular, designed for immersion depths of up to 9 meters
It is worth noting that this equipment is suitable for use in hot climates, as it works without interruption even at 50 degrees heat.
Belamos XK 08 ALL
This is a pumping station manufactured in Belarus - has similar characteristics and is in the same price category. With a power of 800 W, it provides a capacity of about 3 m³ of water per hour.
The Belamos XK pumping station, made in Belarus, is a worthy alternative to the Whirlwind, both in terms of performance and price.
This pumping station can be used both with a well or a well, and when connected to a main water supply. In any case, it will provide the necessary pressure of water.
Recommendations for choosing a pumping station for a summer residence are given in this article, and for a private house - here.
Here you can see an overview of various models of pumping stations:
This video contains useful recommendations for choosing a pumping station, taking into account operating conditions:
If the equipment is selected correctly, it will work for a long time and without breakdowns. A pump station is a great way to provide sufficient pressure in the water system of a house to make it truly comfortable.
Looking for an efficient and inexpensive pumping station? Or have experience using such installations? Please leave comments on the article and share your impressions of the use of pumping stations.